Working with ‘Palight’ foamed Pvc

I’m really very keen now to get a better idea of just how many people are working with this wonderful stuff or have even heard of it? I’ve been working with it for years having been introduced to it by a good model-maker friend from the US. I’ve always assumed it must be well known to architectural and product model-makers here in the UK but since I don’t mix with them (as much as I might like) I’m really not sure anymore. Another reason for my doubt is that 4D in London are now planning to stock it (partly at my suggestion) but they’ve always been very much in touch with what their customers might be looking for and obviously haven’t noted a significant enough demand up to now. Even though many established freelancers or model-making firms may be more likely to order in bulk from other sources the ‘knowledge’ does normally tend to filter through to the rest of the community. So I’d be very grateful for any feedback on this i.e. whether you’ve heard of it and from where, whether you use it and for what?

The following ‘article’ is a transcript of the guidance sheet I’ve put together especially for 4D in conjunction with their presentation of my 1:25 scale teaching kit in the shop later in May (see previous post May1st). Therefore there’s some emphasis on small-scale work but foamed Pvc is available in thicknesses up to 20mm making it applicable for virtually any scale of work! I’ve also just started to compile a directory of materials accessed from the ‘header’ menu above in which I will group information like this according to material.

Foamed Pvc is an extremely versatile sheet plastic. Of all the different brands I’ve tried over the years Palight has proved to be by far the easiest to work with by hand. In fact it’s become my own first choice as the basis for almost everything I make! It can be easily cut with a scalpel, or carved, sanded, even embossed to a certain extent. It can be painted without any danger of warping (though it will usually require priming first) is not affected by humidity or (within reason) heat from strong lights. It is also incredibly light! For example, when I use it to make larger-scale sets for stop motion animation it delivers the structural strength of Mdf at a fraction of the weight! The only caveat in all this is the fact that it can only be glued with superglue, but on the other hand this gives a very strong bond and also once one has mastered the option of ‘gluing from outside’ it all becomes much easier!

I’ve chosen and illustrated three examples of its use: firstly using 1mm Pvc (the thinnest available) for intricate forms; secondly using 2mm Pvc for general construction; thirdly using Pvc as one may not otherwise have expected, to create surface effects.

Although it’s much easier to draw on foamed Pvc with a pencil (unlike styrene or Abs) I prefer to work out a design on paper and spraymount a copy on the plastic. In the photo below I have started cutting out the ironwork shape through the paper. Curves are much easier with Pvc than cardboard because the composition is much smoother, with no particles or fibres to affect the passage of the blade. Cutting is easier also because it is more porous (foamed) on the inside and will ‘give’ a little under the blade causing much less friction.

If the paper cutting template is lightly fixed with spraymount (especially the repositionable type) it can be easily peeled off the form once cut.

In this case the Pvc cut-out serves as a firm, cleanly cut basis upon which more detail, profiling or strengthening can be added on top. It’s a constructional principle of ‘building in layers’ which I’ve developed for myself over the years and try to follow most of the time. Below I’m adding a strip of styrene (a harder plastic which can be bought in a wide variety of pre-made strip formats) to make a thicker top rail. The easiest way to glue this on in exactly the right place first time is to position a guide-block (in this case a metal block) against the top, press the cut length of styrene against it and run a little thin superglue (using a plastic gluing brush or cocktail stick if preferred) along the join. The thin type of superglue will travel into the join and set immediately.

Below, I am doing similar but this time with a very thin (c. 1mm) cut strip of the same Pvc to give the arches more substance. Pvc is nicely bendable, especially in thin strips. The trick with bonding a strip in an exact curve is to fix the strip with a spot of glue at one end first, then curve and position the rest, ‘spot-gluing’ at intervals to the other end. I’ve cut the strip a little longer, to be trimmed off when the end is reached.

The following example illustrates some of the benefits of using foamed Pvc to construct walls etc. Even thin Pvc will retain its rigidity well. For example 1mm Pvc can be used to represent walls up to 30cm high easily, as long as they’re not load-bearing. Because Pvc sands well cut edges can be cleaned up if uneven and right-angles bettered prior to gluing together. Also because Pvc sands well the visible joins after gluing can be sanded often to invisibility!

In the next example I am constructing a piece of vaulted ceiling by first making a framework box (2mm Pvc) and then curving a thinner piece of Pvc underneath it. Curves are much easier to cut smoothly in Pvc because there is no grain and the material ‘gives’ a little. It is also possible to make a definite guiding groove in the soft surface using a compass fitted with two metal points. Curves can also be perfected by sanding them.

Here I have scored the 1mm on one side to help it to bend. The same can be done by heating it uniformly and securing it until cool on a curved surface such as a bottle. The piece can be glued in position, in much the same way as the curved profiles on the ironwork example, by first securing one end, pressing the rest into position and ‘spot- gluing’ from outside. Here the end has been made purposely longer and can be easily trimmed off once the rest is glued.

Whereas other plastics such as styrene or Abs can be sanded to modify the surface, because foamed Pvc ‘gives’ so much more it can be inscribed or even embossed to create different textures. Here is just one example where I have scraped the surface with coarse sandpaper to simulate wood.

To build up the structure of wood panelling I first cut out the raised areas as continuous pieces, then pressed firmly with sandpaper (120 grit, mounted on a small block) along the length of each part. ‘Grain follows length’ almost always for any realistic wood construction.

I scraped those areas of the base piece which would remain visible as panels then stuck the frames into position (just spacing dots of superglue). I used different thicknesses of ‘half-round’ profile styrene (also sanded) inside the panels and around the door frame.

The painting method and the choice of medium are fairly crucial in making this technique work. Normally it wouldn’t  be reasonable to paint plastic with any water-based paint  and expect it to stay, but because the surface is sanded it can grip quite well. The paint needs to emphasize the scratches made by the sandpaper, settling well in the grooves but not too much on the surface. Sometimes this can be achieved well with washes of thin paint, other times by rubbing in/rubbing off like a polish. For this example I just used a regular System3 yellow ochre acrylic thinned down with a little water and ‘rubbed into’ the plastic surface using a medium-hard brush. It takes some practise to find out for oneself what a particular painting medium might do and how best to do it.

8 thoughts on “Working with ‘Palight’ foamed Pvc

    • Hello Tina,

      I know only what I’ve written here .. namely that the only glue guaranteed to work strongly is superglue, presumably any brand of cyanoacrylate. PVC solvent (used by plumbers) works in a way but the bond is not strong. I very much doubt that any UHU would take strongly enough.

    • Is there HomeDepot in Canada? Palram, the makers of Palight, are introducing it there .. but costing a bit more I think! Otherwise, Palram is a global company with strong presence in the US so I wouldn’t have thought there would be a problem getting it in Canada? Just Google it. Let me know what you find out and I can add it to advice about suppliers in the longer version of this article in the ‘Materials/Constructing’ section.

  1. Hi David another interesting piece from you. Although I have heard of it, I have not used it in my own work. When 4D bring it in I will certainly test it for use. I can see potential benefits as a substitute for Kapa in certain situations.

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s